Contact Us
Contact Us Stock Check

Target - Magnet |

MFM7-APS90-LACD4 Hall Effect Angle Position Sensor

The MFM7-APS90-LACD4 Hall Effect Angle Position Sensor operate at 8 to 32 VDC and provide 0-5V analog output over 90 degrees of rotation. “APS” type Angle Position Sensors are non-contact sensors that detect a marked magnet to define orientation. The output is proportional to the angle. The flange mount housing installation ensures proper orientation and gap from the target magnet. The MFM7-APS90-LACD4 Angle Position Sensor has a regulated and load dump protected input with linear analog output. A ratiometric output to internal 5 V regulator, analog ref. output wire can be connected for regulator tolerance. Furthermore, the sensor is potted in a flange mount housing with Deutsch DT04 4-pin connector. Target Magnet Sold Separately

The “Discontinuity Point” is the angle where the output changes from 0V to 5V. This is intentionally programmed to be as far away from the actual Linear Range as possible. With this, if the magnet goes past 0 degrees the output stays 0V; and if it goes past 90 degrees the output stays 5V.

Note: The operate gap range is dependent on the target magnet. Refer to the specifications chart for magnet options and gap ranges. Contact us for 0 to 5 V angle position sensors for other degrees of rotation!

Other features include:

  • Non-contact
  • Resistant to Shock & Vibration
  • Linear Voltage Output
  • Output Over 90 Degrees of Rotation
  • 5V or Regulated Versions
MFM7-APS360-LACD4 Hall Effect Angle Position Sensor

The MFM7-APS360-LACD4 Hall Effect Angle Position Sensor operate at 8 to 32 VDC and provide 0-5V analog output over 360 degrees of rotation. “APS” type Angle Position Sensors are non-contact sensors that detect a marked magnet to define orientation. The output is proportional to the angle. The flange mount housing installation ensures proper orientation and gap from the target magnet. The MFM7-APS360-LACD4 Angle Position Sensor has a regulated and load dump protected input with linear analog output. A ratiometric output to internal 5 V regulator, analog ref. output wire can be connected for regulator tolerance. Furthermore, the sensor is potted in a flange mount housing with Deutsch DT04 4-pin connector. Target Magnet Sold Separately

The “Discontinuity Point” is the angle where the output changes from 0V to 5V. This is intentionally programmed to be as far away from the actual Linear Range as possible. With this, if the magnet goes past 0 degrees the output stays 0V; and if it goes past 360 degrees the output stays 5V.

Note: The operate gap range is dependent on the target magnet. Refer to the specifications chart for magnet options and gap ranges. Contact us for 0 to 5 V angle position sensors for other degrees of rotation!

Other features include:

  • Non-contact
  • Resistant to Shock & Vibration
  • Linear Voltage Output
  • Output Over 360 Degrees of Rotation
  • 5V or Regulated Versions
MFM7-APS180-LACD4 Hall Effect Angle Position Sensor

The MFM7-APS180-LACD4 Hall Effect Angle Position Sensor operate at 8 to 32 VDC and provide 0-5V analog output over 180 degrees of rotation. “APS” type Angle Position Sensors are non-contact sensors that detect a marked magnet to define orientation. The output is proportional to the angle. The flange mount housing installation ensures proper orientation and gap from the target magnet. The MFM7-APS180-LACD4 Angle Position Sensor has a regulated and load dump protected input with linear analog output. A ratiometric output to internal 5 V regulator, analog ref. output wire can be connected for regulator tolerance. Furthermore, the sensor is potted in a flange mount housing with Deutsch DT04 4-pin connector. Target Magnet Sold Separately

The “Discontinuity Point” is the angle where the output changes from 0V to 5V. This is intentionally programmed to be as far away from the actual Linear Range as possible. With this, if the magnet goes past 0 degrees the output stays 0V; and if it goes past 180 degrees the output stays 5V.

Note: The operate gap range is dependent on the target magnet. Refer to the specifications chart for magnet options and gap ranges. Contact us for 0 to 5 V angle position sensors for other degrees of rotation!

Other features include:

  • Non-contact
  • Resistant to Shock & Vibration
  • Linear Voltage Output
  • Output Over 180 Degrees of Rotation
  • 5V or Regulated Versions
A63-APS360-LACB1E Hall Effect Angle Position Sensor

The A63-APS360-LACB1E Hall Effect Angle Position Sensor operate at 8 to 32 VDC and provide 0-5V analog output over 360 degrees of rotation. “APS” type Angle Position Sensors are non-contact sensors that detect a marked magnet to define orientation. The output is proportional to the angle. The flange mount housing installation ensures proper orientation and gap from the target magnet. The A63-APS360-LACB1E Angle Position Sensor has a regulated and load dump protected input with linear analog output. A ratiometric output to internal 5 V regulator, analog ref. output wire can be connected for regulator tolerance. Provided lock nuts used to set air gap and orientation to magnet. Target Magnet Sold Separately

The “Discontinuity Point” is the angle where the output changes from 0V to 5V. This is intentionally programmed to be as far away from the actual Linear Range as possible. With this, if the magnet goes past 0 degrees the output stays 0V; and if it goes past 360 degrees the output stays 5V.

Note: The operate gap range is dependent on the target magnet. Refer to the specifications chart for magnet options and gap ranges. Contact us for 0 to 5 V angle position sensors for other degrees of rotation!

Other features include:

  • Non-contact
  • Resistant to Shock & Vibration
  • Linear Voltage Output
  • Output Over 360 Degrees of Rotation
  • 5V or Regulated Versions
S63B-DHS1-5KCB2A Hall Effect Dual Switch Sensor

The S63B-DHS1-5KCB2A Hall Effect Dual Switch Sensor produces dual pulsing outputs, 1 south pole and 1 north pole. Dual output Hall Switch Sensors function as a directional limit switch. “DHS1” type Dual Hall Effect Sensors have a 55 gauss operate point. The S63B-DHS1-5KCB2A Dual Hall Switch Sensor has an NPN input with a 5k pull up resistor.  Furthermore, the sensor is potted in a stainless steel 5/8-18 cylindrical housing with integral connector.

When the south pole element is close to the sensor face, channel A output goes low and the sensor switches on, while Channel B output goes high and switches off. The sensor can detect the south pole magnet at a slightly greater operate gap than the north pole element. Conversely, when the north pole element is close to the sensor face, channel B output goes low and switches on, while channel A output goes high and switches off. So, a south pole detection turns channel A on, while a north pole detection turns channel B on.

No rotational sensor orientation is required for operation. Use the provided lock nuts to set the air gap from the target. Note: Operate and release gaps are dependent on the size, material, grade, and temperature of the target magnet. 

Other features include:

  • True Zero Speed
  • Rugged, Sealed Housing
  • Greater Detection Gap than Standard DHS Sensor
  • Solid State (Nothing to wear out!)
S12-DHS1-5KSA5 Hall Effect Dual Switch Sensor

The S12-DHS1-5KSA5 Hall Effect Dual Switch Sensor produces dual pulsing outputs, 1 south pole and 1 north pole. Dual output Hall Switch Sensors function as a directional limit switch. “DHS1” type Dual Hall Effect Sensors have a 55 gauss operate point. The S12-DHS1-5KSA5 Dual Hall Switch Sensor has an NPN input with a 5k pull up resistor.  Furthermore, the sensor is potted in a plastic M12 cylindrical housing with shielded 4-wire 22 AWG PVC cable.

When the south pole element is close to the sensor face, channel A output goes low and the sensor switches on, while Channel B output goes high and switches off. The sensor can detect the south pole magnet at a slightly greater operate gap than the north pole element. Conversely, when the north pole element is close to the sensor face, channel B output goes low and switches on, while channel A output goes high and switches off. So, a south pole detection turns channel A on, while a north pole detection turns channel B on.

No rotational sensor orientation is required for operation. Use the provided lock nuts to set the air gap from the target. Note: Operate and release gaps are dependent on the size, material, grade, and temperature of the target magnet. 

Other features include:

  • Rugged, Sealed Housing
  • Greater Detection Gap than Standard DHS Sensor
  • Solid State (Nothing to wear out!)
MFM7-DHS1-5KCD4 Hall Effect Dual Switch Sensor

The MFM7-DHS1-5KCD4 Hall Effect Dual Switch Sensor produces dual pulsing outputs, 1 south pole and 1 north pole. Dual output Hall Switch Sensors function as a directional limit switch. “DHS1” type Dual Hall Effect Sensors have a 55 gauss operate point. The MFM7-DHS1-5KCD4 Dual Hall Switch Sensor has an NPN input with a 5k pull up resistor.  Furthermore, the sensor is potted in a flange mount housing with Deutsch DT04 4-pin connector.

When the south pole element is close to the sensor face, channel A output goes low and the sensor switches on, while Channel B output goes high and switches off. The sensor can detect the south pole magnet at a slightly greater operate gap than the north pole element. Conversely, when the north pole element is close to the sensor face, channel B output goes low and switches on, while channel A output goes high and switches off. So, a south pole detection turns channel A on, while a north pole detection turns channel B on.

No rotational sensor orientation is required for operation. Use the provided lock nuts to set the air gap from the target. Note: Operate and release gaps are dependent on the size, material, grade, and temperature of the target magnet. 

Other features include:

  • True Zero Speed
  • Rugged, Sealed Housing
  • Greater Detection Gap than Standard DHS Sensor
  • Solid State (Nothing to wear out!)

SUBSCRIBE TO OUR NEWSLETTER

We Will Use The Email Address You Provide To Send You Marketing And Promotional Materials.

Tradeshows & Events

Follow Us

Focused. Leadership

Video
Download Table
Products compare