Angle Position Sensor products use Hall Effect Technology to detect a magnets' angle in degrees of rotation. This non-contact rotary position sensor uses an actuator magnet (sold separately) that is marked to define the orientation. These Hall Sensors provide 0-5 V linear analog voltage output over some degree of rotation. Our standard detection angles are 90, 180, and 360 degrees. All of our Hall Effect sensors can be modified, enhanced, or updated with our modular features and functionality. Choose from various housings in aluminum, stainless-steel, plastic, threaded, flange mount, and customer specific. Available sensor functionality includes NPN, PNP, TTL, etc. Connectivity options such as Deutch, Amphenol and many others, free-end wires pigtails, any length. Contact us for additional 0-5 V or optional regulated Angle Position Sensor versions.
The AM-M1H2-04022S Magnet for Angle Position Sensors is a potted radial magnetized magnet. The Housing measures 1.0-inch x 0.5 inches and features 2 Mounting Holes. The raw magnet produces 400 Gauss at .060″ and 200 Gauss at 0.215″ Gap. Using this housing, operate the APSxxx sensors using a sensing gap from 0.010″ to 0.110″.
NOTES:
Contact Sensor Solutions to discuss custom sensor and magnet requirements for your application.
The RM-01-071 Magnet for Angle Position Sensors is a radial magnetized bare magnet. This Neodymium magnet measures 0.500 inches in diameter by 0.125 inches long. Furthermore, the magnet is North “N” and South “S” Pole marked.
NOTES:
Contact Sensor Solutions to discuss custom sensor and magnet requirements for your application.
The MFM7-APS90-LACD4 Hall Effect Angle Position Sensor operate at 8 to 32 VDC and provide 0-5V analog output over 90 degrees of rotation. “APS” type Angle Position Sensors are non-contact sensors that detect a marked magnet to define orientation. The output is proportional to the angle. The flange mount housing installation ensures proper orientation and gap from the target magnet. The MFM7-APS90-LACD4 Angle Position Sensor has a regulated and load dump protected input with linear analog output. A ratiometric output to internal 5 V regulator, analog ref. output wire can be connected for regulator tolerance. Furthermore, the sensor is potted in a flange mount housing with Deutsch DT04 4-pin connector. Target Magnet Sold Separately
The “Discontinuity Point” is the angle where the output changes from 0V to 5V. This is intentionally programmed to be as far away from the actual Linear Range as possible. With this, if the magnet goes past 0 degrees the output stays 0V; and if it goes past 90 degrees the output stays 5V.
Note: The operate gap range is dependent on the target magnet. Refer to the specifications chart for magnet options and gap ranges. Contact us for 0 to 5 V angle position sensors for other degrees of rotation!
Other features include:
The MFM7-APS360-LACD4 Hall Effect Angle Position Sensor operate at 8 to 32 VDC and provide 0-5V analog output over 360 degrees of rotation. “APS” type Angle Position Sensors are non-contact sensors that detect a marked magnet to define orientation. The output is proportional to the angle. The flange mount housing installation ensures proper orientation and gap from the target magnet. The MFM7-APS360-LACD4 Angle Position Sensor has a regulated and load dump protected input with linear analog output. A ratiometric output to internal 5 V regulator, analog ref. output wire can be connected for regulator tolerance. Furthermore, the sensor is potted in a flange mount housing with Deutsch DT04 4-pin connector. Target Magnet Sold Separately
The “Discontinuity Point” is the angle where the output changes from 0V to 5V. This is intentionally programmed to be as far away from the actual Linear Range as possible. With this, if the magnet goes past 0 degrees the sensor output will go up to 5V and if the magnet goes past 360 degrees the output drops to 0V.
Note: The operate gap range is dependent on the target magnet. Refer to the specifications chart for magnet options and gap ranges. Contact us for 0 to 5 V angle position sensors for other degrees of rotation!
Other features include:
The MFM7-APS180-LACD4 Hall Effect Angle Position Sensor operate at 8 to 32 VDC and provide 0-5V analog output over 180 degrees of rotation. “APS” type Angle Position Sensors are non-contact sensors that detect a marked magnet to define orientation. The output is proportional to the angle. The flange mount housing installation ensures proper orientation and gap from the target magnet. The MFM7-APS180-LACD4 Angle Position Sensor has a regulated and load dump protected input with linear analog output. A ratiometric output to internal 5 V regulator, analog ref. output wire can be connected for regulator tolerance. Furthermore, the sensor is potted in a flange mount housing with Deutsch DT04 4-pin connector. Target Magnet Sold Separately
The “Discontinuity Point” is the angle where the output changes from 0V to 5V. This is intentionally programmed to be as far away from the actual Linear Range as possible. With this, if the magnet goes past 0 degrees the output stays 0V; and if it goes past 180 degrees the output stays 5V.
Note: The operate gap range is dependent on the target magnet. Refer to the specifications chart for magnet options and gap ranges. Contact us for 0 to 5 V angle position sensors for other degrees of rotation!
Other features include:
The A63-APS360-LACB1E Hall Effect Angle Position Sensor operate at 8 to 32 VDC and provide 0-5V analog output over 360 degrees of rotation. “APS” type Angle Position Sensors are non-contact sensors that detect a marked magnet to define orientation. The output is proportional to the angle. The flange mount housing installation ensures proper orientation and gap from the target magnet. The A63-APS360-LACB1E Angle Position Sensor has a regulated and load dump protected input with linear analog output. A ratiometric output to internal 5 V regulator, analog ref. output wire can be connected for regulator tolerance. Provided lock nuts used to set air gap and orientation to magnet. Target Magnet Sold Separately
The “Discontinuity Point” is the angle where the output changes from 0V to 5V. This is intentionally programmed to be as far away from the actual Linear Range as possible. With this, if the magnet goes past 0 degrees the sensor output will go up to 5V and if the magnet goes past 360 degrees the output drops to 0V.
Note: The operate gap range is dependent on the target magnet. Refer to the specifications chart for magnet options and gap ranges. Contact us for 0 to 5 V angle position sensors for other degrees of rotation!
Other features include:
® Copyright 2025 Standex Electronics, Inc. ® All Rights Reserved. A Standex International Corporation Company.
