The MFM7-37ADSO-ODX0B Hall Effect Gear Tooth Sensor is a large dynamic speed sensor. “DSO” type Hall Effect Sensors are digital single square wave output target trackers that detect 0-32 pitch gears and ferrous targets. Additional targets include ferrous bolt heads, holes in steel plates, and other magnetic targets.
The MFM7-37ADSO-ODX0B Sensor uses an N Channel open drain output. Furthermore, the sensor is potted in a plastic flange mount housing with free end XLPE 20 AWG wires.
DSO Gear Tooth Sensors have a self-calibrating output that reacts to both the leading and falling edge of any ferrous metal target. No rotational orientation is required for the sensor to operate. Set the air gap relative to the sensing target face with the easy install flange mount design. The MFM7-37ADSO-ODX0B sensor operates in the presence of a magnetic field, which causes the PNP output to go high.
Other features include:
| Output Type | N Channel Open Drain |
| Actuator Material | Ferrous Metals, Gear Tooth |
| Frequency | 15 kHz |
| Supply Voltage, Vcc | 4.2 ~ 24 V |
| Operating Temp. | -40 ~ 110 C |
| Package/Case | Flange Mount |
| Termination Style | Wire Leads |
Aerospace, Agricultural, Automotive/Heavy Equipment, Consumer Electronics, Manufacturing, Marine, Medical, Military, Power Generation, Transportation
Series Data Sheet (PDF)
| Item No. | Datasheet | Distributor | Region | Quantity | Cart | RFQ | Inventory Date |
|---|---|---|---|---|---|---|---|
| MFM7-37ADSO-P5P21 | MASTER/ONLINE | Americas | 0 | RFQ | 2024-10-06 | ||
| MFM7-37ADSO-P5P21 | Digi-Key Electronics | Americas | 10 | BUY | RFQ | 2024-10-06 | |
| MFM7-37ADSO-P5P21 | Standex Factory | Americas | 0 | RFQ | 2024-10-06 | ||
| MFM7-37ADSO-P5P21 | Mouser Electronics | Americas | 0 | RFQ | 2024-10-06 | ||
| MFM7-37ADSO-P5P21 | Arrow Electronics | Americas | 10 | BUY | RFQ | 2024-10-06 | |
| MFM7-37ADSO-P5P21 | TTI Inc Global Headquarters | Americas | 0 | RFQ | 2024-10-06 |
| Mounting Style | Function Type | Sensing Range - On / Off (Gauss) | Voltage Supply (VDC) | Current Supply (mA) | Output Leakage Current Max. (μA) | Output On Voltage Typ. (mV) | Chopping Frequency Typ. (KHz) | Operating Temperature (°C) | Cable Length (mm) |
|---|---|---|---|---|---|---|---|---|---|
The A44-18ADSO-P5P21 Hall Effect Gear Tooth Sensor is a dynamic speed sensor. “DSO” type Hall Effect Sensors are digital single square wave output target trackers that detect 0-32 pitch gears and ferrous targets. Additional targets include ferrous bolt heads, holes in steel plates, and other magnetic targets.
The A44-18ADSO-P5P21 Sensor uses PNP output with a 5k resistor. Furthermore, the sensor is potted in a black anodized aluminum barrel housing with free end wire leads.
DSO Gear Tooth Sensors have a self-calibrating output that reacts to both the leading and falling edge of any ferrous metal target. No rotational orientation is required for the sensor to operate. Lock nuts are used to set the air gap within the rage of the sensing target. The A44-18ADSO-P5P21 sensor operates in the presence of a magnetic field, which causes the PNP output to go high.
Other features include:
The S12-18ADSO-5KCB2 Hall Effect Gear Tooth Sensor is a dynamic speed sensor. “DSO” type Hall Effect Sensors are digital single square wave output target trackers that detect 0-32 pitch gears and ferrous targets. Additional targets include ferrous bolt heads, holes in steel plates, and other magnetic targets.
The S12-18ADSO-5KCB2 Sensor uses NPN output with a 5k pull up resistor. Furthermore, the sensor is potted in a stainless steel M12 cylindrical housing with integrated connector.
DSO Gear Tooth Sensors have a self-calibrating output that reacts to both the leading and falling edge of any ferrous metal target. No rotational orientation is required for the sensor to operate. Lock nuts are used to set the air gap within the rage of the sensing target. The S12-18ADSO-5KCB2 sensor operates in the presence of a magnetic field, which causes the NPN output to go low.
Other features include:
The MFM7-37ADSO-L5CD3 Hall Effect Gear Tooth Sensor is a large dynamic speed sensor. “DSO” type Hall Effect Sensors are digital single square wave output target trackers that detect 0-32 pitch gears and ferrous targets. Additional targets include ferrous bolt heads, holes in steel plates, and other magnetic targets.
The MFM7-37ADSO-L5CD3 Sensor uses load dump and EMI protected input and NPN output with a 5k pull up resistor. Furthermore, the sensor is potted in a plastic flange mount housing with wire leads and Deutsch DT 3 pin connector.
DSO Gear Tooth Sensors have a self-calibrating output that reacts to both the leading and falling edge of any ferrous metal target. No rotational orientation is required for the sensor to operate. Set the air gap relative to the sensing target face with the easy install flange mount design. The MFM7-37ADSO-L5CD3 sensor operates in the presence of a magnetic field, which causes the NPN output to go low.
Other features include:
The MFM61O-18ADSO-L5CP13 Hall Effect Gear Tooth Sensor is a dynamic speed sensor. “DSO” type Hall Effect Sensors are digital single square wave output target trackers that detect 0-32 pitch gears and ferrous targets. Additional targets include ferrous bolt heads, holes in steel plates, and other magnetic targets.
The MFM61O-18ADSO-L5CP13 Sensor uses surge protected input and NPN output with a 5k pull up resistor. Furthermore, the sensor is potted in a plastic flange mount housing with integrated 3-way Metri-Pack male connector.
DSO Gear Tooth Sensors have a self-calibrating output that reacts to both the leading and falling edge of any ferrous metal target. No rotational orientation is required for the sensor to operate. Set the air gap relative to the sensing target face with the easy install flange mount design. The MFM61O-18ADSO-L5CP13 sensor operates in the presence of a magnetic field, which causes the NPN output to go low.
Other features include:
The MFM7-37ADSO-L5CP13 Hall Effect Gear Tooth Sensor is a large dynamic speed sensor. “DSO” type Hall Effect Sensors are digital single square wave output target trackers that detect 0-32 pitch gears and ferrous targets. Additional targets include ferrous bolt heads, holes in steel plates, and other magnetic targets.
The MFM7-37ADSO-L5CP13 Sensor uses load dump and EMI protected input and NPN output with a 5k pull up resistor. Furthermore, the sensor is potted in a plastic flange mount housing with wire leads and Deutsch DT 3 pin connector.
DSO Gear Tooth Sensors have a self-calibrating output that reacts to both the leading and falling edge of any ferrous metal target. No rotational orientation is required for the sensor to operate. Set the air gap relative to the sensing target face with the easy install flange mount design. The MFM7-37ADSO-L5CP13 sensor operates in the presence of a magnetic field, which causes the NPN output to go low.
Other features include:
The MFM7-37ADSO-P5P21 Hall Effect Gear Tooth Sensor is a large dynamic speed sensor. “DSO” type Hall Effect Sensors are digital single square wave output target trackers that detect 0-32 pitch gears and ferrous targets. Additional targets include ferrous bolt heads, holes in steel plates, and other magnetic targets.
The MFM7-37ADSO-P5P21 Sensor uses PNP output with a 5k resistor. Furthermore, the sensor is potted in a plastic flange mount housing with free end wire leads.
DSO Gear Tooth Sensors have a self-calibrating output that reacts to both the leading and falling edge of any ferrous metal target. No rotational orientation is required for the sensor to operate. Set the air gap relative to the sensing target face with the easy install flange mount design. The MFM7-37ADSO-P5P21 sensor operates in the presence of a magnetic field, which causes the PNP output to go high.
Other features include:
AI Industry's stronger demand for power and test equipment drive reed switch, sensor, and relay use.
Ralf Maier speaks to the AI Industry's impact on Reed technology use. "We are continuously developing new products for all our three product lines. We have the reed switches, sensors and relays. The AI industry has a stronger demand for power, but also a stronger demand for test equipment. This test equipment is used around the semiconductor fabrication and our products, especially the reed relays, are used in unique test equipment around the world to support these industries. Reed technology is used in almost every market. I think in your daily life you come across reed products every day. They are used in appliances such as washing machines and fridges, but they also used in security products like door alarm systems. But then we just talked about the semiconductor test equipment. Many, many reed relays are used there.
And one of our biggest markets is transportation and automotive where the electric vehicles take a large market share. Obviously, the last few years were very challenging for all the industry manufacturers. We have 10 factories around the world, and we have some unique capabilities, but also capabilities we have in different sites. So, we can support our customers in all the major regions directly with our processes and products. So, our intention is to continue to grow and to diversify our product portfolio. We have a strong road map for all three product lines for the reed switches, the sensors and the relays, and we continuously invest into new processes to be more efficient. Standex Electronics is your partner for sensing and switching solutions across the globe. We enable an electrified future."
Reflecting on a successful week at Electronica China, we at Standex Electronics are invigorated by the connections we've made and the opportunities that lie ahead. Our participation in this premier event has not only allowed us to showcase our cutting-edge solutions from Sanyu but also to engage in meaningful dialogue with industry peers and customers.
Our commitment to innovation was met with enthusiasm, and we're excited to foster the new relationships built during the tradeshow. The synergy between problem-solving and customer satisfaction is what drives us forward. Here's to transforming these engagements into enduring partnerships and continuing to lead with innovation in the electronics sector.
Welcome to Standex Electronics' How to Select the Correct Technology for a Given Sensor Requirement. We will focus on the following sensor technologies - Reed, Hall, and Electromechanical. These sensors all provide a switching function either directly or indirectly. We will introduce the key specifications, and how these parameters compare to each other for the different technologies.
® Copyright 2024 Standex Electronics, Inc. ® All Rights Reserved. A Standex International Corporation Company.
